Loft Boarding Guideline
Do you want to know how to get into a loft? Everything you need to know about boarding a loft is included in this post, from a detailed how-to to a rundown of the equipment and supplies you’ll need.
Is Loft Boarding Necessary?
Adding boards to your loft will not only make it more solid and secure, but will also enhance the space you have to store things.
If you’re short on closet space, this will come in very handy.
DIY Loft Access Guide
The first thing to do is to take a measurement from joist centre to joist centre. The number of loft legs can then be determined with more accuracy.
The next step is to determine the appropriate board sizes. The standard thickness of loft floor boarding is 18mm.
The second step is to measure the loft space and determine how many sheets are needed to cover it based on the size of the sheets you plan to use.
Third, if any downlights are installed in the ceiling, a downlight cover or protector should be installed over them. Make sure the insulation is kept away from the light fixture.
The fourth step is to begin in an accessible area, like by the attic door, and make your way to the other side. Put the first loft leg in place with the help of a cordless drill. The screws should be inserted through the holes in the lower leg and into the joist.
Step 5: Mark the locations of the loft legs on additional joists using the straight edge, and then proceed to screw the legs into place using the same procedure.
Step 6: Continue doing this across the joists until all of the space you intend to board is supported by legs.
The seventh step is to roll the insulation into place. Carefully cut an incision with a trimming knife where the insulation meets a loft leg, and then push the leg through the insulation. You should do this all the way along the loft’s length.
After the insulation has been set up in Step 7, you may move on to installing the loft boards in Step 8. Put the first sheet on the loft legs and secure it by screwing through the board and into the loft leg’s platform.
It’s possible that step 9′s loft planks have a tongue and groove assembly. As you continue to install the boards next to one another, double-check that everything is snug.
Use this method to fasten all of the loft planks to the legs. Some lofts may require that you modify the length of the boards to get them past impediments or to fit the available area.
After step 10, the floor is complete when you can stand and walk on it without worrying about the boards shifting.
- Equipment for Entering a Loft
- A measuring tape
- Power tool and attachments
- Crayons Hand saw Pruning shears
- Precautions to Take Before Entering a Loft
- Construction gloves
- Protective gear for dust
- Safety glasses
- knee protectors
- Building Supplies for a Loft
- A shield for or protection for downlights
- Tall thighs
- Roofing tins
- Rolls of insulation (if the existing insulation is too shallow).
Preparing to Enter a Loft
You should empty your loft of any personal belongings before you board it up. Before you start boarding, you need also make sure your loft is adequately insulated.
In order to meet regulatory regulations, your insulation must be at least 270 mm thick whenever it is installed.
The floor joists need to be clearly seen so that people know where to walk. In order to see the joists, extra insulation must be removed.
It’s important to check the loft’s safety and the ladder’s stability before beginning the project.
Also, make sure there’s plenty of lighting in the loft so that everyone can walk around comfortably and get the job done.
It’s also important to check the loft’s ventilation before beginning any work there.
Rules for Attic Insulation
Planning authorization and construction requirements must be considered before loft boarding is done to ensure compliance.
If you want to solely store objects weighing less than 25 kilogrammes in your loft after you board it, you won’t need permission from building regulations.
The insulation in the loft must also be kept at a depth of 270mm. One hundred millimetres of depth was once required. This changed in 2013, although homeowners are exempt from extending their buildings to meet the new standards.
Converting your attic into a liveable area, however, will necessitate applications for both planning permission and building requirements.
Various Loft Boarding Options
Although there are various options for boarding a loft, loft legs are by far the most effective. This will guarantee that your loft insulation is up to code with the law. The various loft boarding options are as follows:
Putting Down Chipboard On top of the joists
This method of boarding is inexpensive and simple to set up. However, the recommended insulation depth is not accommodated by this form of boarding, and the insulation may be squeezed, leading to moisture and mould.
Boards for Insulation
Insulation boards can be bought and installed directly onto the joists. You can then install chipboard on top of these boards, which will cover up the insulating depth.
These boards are pricey and might limit ventilation, leading to moisture and mildew.
A Case for Loft Legs
Using loft legs, the floor may be raised. The standard by which all other loft boards are measured. It leaves enough space under the floor for insulation and allows for good air circulation, which eliminates the possibility of condensation and dampness.
How can I board a loft with insulation already present?
The insulation should be raised above the boarded area if you are boards over it. Safer boarding heights can be achieved with the use of devices like loft legs.
To what extent should I board my attic?
Most homeowners, in fact, like to board up the whole loft. However, that is not a need. How much you board depends entirely on your own individual preferences and requirements.
How will the loft flooring I choose affect the insulation?
Following the instructions in our how-to guide, you can avoid having your loft’s flooring affect the insulation by elevating the boarding on loft legs.
How much body mass can be supported by loft boarding?
Loft floor joists in the UK can typically support 40 kilogrammes per square metre of weight. Overstuffing your loft can cause the joists to sag, which in turn can cause cracks in the ceilings below.
If you plan to store a lot of stuff in your loft, you should try to distribute that weight as evenly as possible.
Does installing loft boards necessitate a building permit?
Loft boarding for residential storage reasons does not necessitate a building permit in most jurisdictions. However, you will need to obtain a building permit before converting your loft into a dwelling area.